Sheet Metal Tools

A colleague from the area oldtimer car I was called and my degree here http://www.blechtools.de/ recommended because he knows that I am in the next few weeks as aluminum plate to the 30 current meter 1.5 mm-1 Series and he just have to cut ... someone has experience with the rem I remember only vaguely heard of it having the (das ding works as stanze) one extreme to the waste-punched parts to watch out because they are so razor-sharp .. who has already worked with them? 've used it a few times. For rundungen or if it is not so well really matters, I find the "nipple" quite well. Well these chips are punched though sharp, but I could not find the so wild. If you aluminum sawing, Wood shavings are also not without! For straight cuts, which will even-mm be accurate, I prefer working with my middle circular saw, which for this Purpose with a special blade is equipped. Now, finally, I've had about 140 linear meters, which were cut, a small Plunge. -> Link The purpose of this was not at bad. Only had for about 80mtr. the saw blade to be changed. I have such a device. But if you hinbekommst clean Grerade so I doubt it. Cutting curves and contours is so super

Take my dear 1 mm cut-off wheels. This Nibbelabf?lle looks like a cut finger nails, I know that also from the steel up to 3-4 mm thick. I have such a device. But if you hinbekommst clean Grerade so I doubt it. Cutting curves and contours is so super Take my dear 1 mm cut-off wheels. This Nibbelabf?lle looks like a cut finger nails, I know that also from the steel up to 3-4 mm thick. I'm on my superior zuzulegen one. I ask because the interface is apparently obscured in part, how does it cut out with the exact. 2. You can start somewhere in the material-cutting? 1 mm cut-off wheels not too bad, But since I have not done such a good experience. Flex has seized up again, and it was then impossible to change the blade. So firm was the screw! Also I get with the Flex, not as clean cut as with a circular saw / Plunge out.

Circular saw with a special steel blade is certainly good for a straight cut. Instead there is the flex of fine (the orange) machinery, a device with oscillating movement. Da gibts no hot chips and cold, the material is cut, so there is no wave or move the material. Can be used as cutting tool but also as a scraper to remove from sealants are used in your case is certainly not bad. So I cut aluminum from a thickness of 1.5 - 2 mm on a circular saw with carbide blade. This is class and is straight. For the chips goggles is required. If, however, only with smaller parts, with long metal plates wirds since been difficult. I'll take up to 1 mm always a tin snips.

Hab so ne stable, straight scissors that cuts through like butter, and even straight. At 30 meters for I would go into a factory and cut with scissors to the blow. It only looks like it can cut very precisely. yes, you can start somewhere to cut. I am well coped with it. The Plunge I cut aluminum and wood laminate. Only the quality of the saw, I'm not from Westfalia, but of skill is not so great! (Typically just DIY) The screw with which the saw blade is mounted is not so great. Also very difficult to get the young blades. I must say the fine multi-master (which I believe, right?) See times I read about it many times in DIY forum but probably I'll risk the blechnibbler such and such time ... on ebay then around 70, - around with the addition halter is so unbearable I highly processed in the last year about 150lm Rohrverbindungssystem 2mm and 3mm, most g?hrungsschnitte after much back and forth I ended up with the flex 125iger with gaanz thin niroscheibe this is really the best

The 1mm steel disc has been going too, but that is already a considerable gemetzel .. Jigsaw has not worked for me, the tears as the henker and four sections need a new sawblade ... But now I must above all not just make pads in 1mm or 1.5 mm aluminum plates, with curves and arches drinne, since hardly what is going on with flex plate and scissors, hence my considerations there are medium format sheets in 250x125cm, since transport is a problem for a professional company and quite honestly, the prices for the laser-dressmaking are not so easily ....

For what you're up to, because suited the "Nippler" determined. My degree has given up just his mind .... Multi-master, yes I also have. I have time this morning a lufts?ge borrowed make the afternoon a couple of times a test sections and see if it works I'm not sure if my air compressor has enough power to But then arises out eh the Fein Multimaster is truly one of the best tools on the market, to cut and polish in the last corner. Only with longer sections This makes no fun, since you only so mm forwards coming. And curves to go with the oscillating saw blade either. I would no longer do the multi-master